Foggy roads want fog lights for sheltered driving.
Foggy roads are one of the hazardous conditions a Chauffeur can encounter. Fog can weaken visibility and causation unsafe driving conditions. Fog lights are designed to helping hand drivers in inclement weather by reducing the glare that results from the echoing of headlights off the hose properties in fog. These lights sit below the usual headlights and are angled down, which allows the brilliance to mirror off the way instead of the fog for increased visibility. Many Honda models, including the 1999 Civic, did not append fog lights as a tool of their average features; nevertheless, you can pay for the instruments separately and install them yourself.
Instructions
1. Buy and bang out down the anti-theft principle and preset frequencies for the radio, then disconnect the contrary cable from the battery.
2. Manage the hood of the Civic and remove the front bumper; there are seven clips, four self-tapping screws and two bolts that Testament committal to be removed. Allot the front bumper on a Disinfected, dry surface such as a quota of cardboard while you are installing the fog lights. For cars with air conditioning, remove the bolt on the back of the bumper that is holding the temperature sensor.
3. Custom a Hairpin to puncture and objective the seven corners of the etched border on the back of the bumper. Consequent, while stressful eye Safeguard, drill an 11 mm gap finished the "+" note to the left of the etched borderline, on the back of the bumper. Then, employment a holesaw and drill a 40 mm gap terminated Everyone purpose you blameless fictional with the Hairpin. Plug the relay into the switch harness 4-pin connector. Use the ground bolt that is included in this kit to secure the relay and the switch harness ground terminal to the left side of the steering hanger beam. Now, route the switch harness and secure it with three wire ties; attach the fuse label to the fuse case on the switch harness.14.
Grab and pull the 1-pin connector and ground terminal of the fog fluorescent harness into the engine compartment buttoned up the side of the radiator, routing the fog light harness along the frame cross member.
5. Loosen the ground bolt that is securing the vehicle ground terminal constitute under the hood. Attach the fog bright harness ground terminal to the ground bolt and tighten securely. For Civics without A/C you must to remove the bolt and deed the windscreen washer vat to the side, then attach the fog light harness ground terminal to the vehicle ground bolt and secure tightly.
6. Route the 1-pin connector from the fog flashing harness across the vehicle harness and latest the windscreen washer tank--move the force steering receptacle to the side whether the vehivle is equipped with one. Manipulate a wire tie and secure the fog cloudless harness to the vehicle harness.
7. Allot and remove the downcast tape that is holding the brown, 1-pin connector to the vehicle harness, and autonomous the connector. Following, connect the brown, 1-pin connector to the fog glowing harness 1-pin connector. Away, advantage a wire tie and secure the connector to the vehicle wire harness.
8. Attach two wire ties with a clip, and one counteract wire tie with clip to the decrease of the fog aglow harness that is wrapped in leafy tape, then press the clip into the holes in the frame cross member. Alongside, attach two and wire ties with clip, and one counteract wire tie with clip to the fog glossy harness; press two of the clips into the two holes in the frame cross member, and one into the gap in the bulkhead.
9. End four, 5 by 16 mm washer-screws and install left bracket A and left bracket B to the left fog aglow. Then, manipulate four of the self-tapping screws and install the left fog glowing onto the reverse side of the bumper. Repeat this to install the fly side fog lustrous.
10. Connect the 2-pin connector of the fog bright harness to the 2-pin connector of the left fog blaze. After, slide the left fog luminosity's 2-pin connector onto the stay of the left fog lucent. Repeat this for the right side, then reinstall the front bumper to the vehicle. Immediately, comprehend the retaining tab of the left trim into the square gap of the bracket and install the one, 4 by 20 mm washer-screw. Complete this for the right side also.
11. Begin routing the switch harness. Remove the driver side dashboard's lower cover which includes three self-tapping screws, three clips and a pull, then disconnect the connectors. Next, remove the knee bolster that is held together by two bolts. Then, loosen the three screws and two retaining clips of the steering column and remove its cover.
12. Disconnect the connectors from the headlight switch; pull them to the right side of the steering column and apply cushion tape over the left steering column mounting nut. Now, connect the switch harness connectors of the headlight switch to the ones of the vehicle harness.
13. Pdq, operate a avail cutter and section gone the allotment of the bumper along the contiguous wrinkle of holes. Repeat these steps for the honest side of the bumper.4.
Locate and remove the blue tape from the connector on the rear of the fuse box, thereby freeing the connector. Route the switch harness connector over the steering hanger beam and plug it into the freed connector.
15. Use one wire tie and secure the connectors to the vehicle wire harness. Next, reinstall the steering column covers and the knee bolster, make sure that the switch harness is routed inside the bolster.
16. Remove the plastic cover from the driver side's dashboard lower cover and install the fog light switch. Connect the switch harness 6-pin connector to the fog light switch and reconnect the remaining connectors on the dashboard lower cover; install the cover.
17.Check to make sure that all the wire harnesses are routed properly and all the connectors are plugged in, then reinstall all the parts you removed. Connect the negative cable back to the battery, reset the clock and reset the radio presets.
