Clogged sunroof drainage tubes Testament sufferance standing H2O on the sunroof channel guides, allowing moisten into the interior when the sunroof is opened. Carefulness these tubes for nothing from any debris is bottom line to make safe the flood is properly drained from the channel guides. Cleaning the tubes in a 1999 Saturn can be done within an time or two by most novice mechanics. On a 1999 Saturn, there are four differential tubes from the four corners of the sunroof channels, two going to the front of the vehicle and two going to the rear.
Instructions
Cleaning the Two Front Drainage Tubes
1. Remove the kick panel under the dashboard on the side of the interior. Pull the kick panel gone from the side of the interior to disengage the metal retaining clips.
2. Pull the rubber grommet to the side to enable access to the rear of the panel revealed when the kick panel was removed. On the Chauffeur side of the vehicle, detach the electrical connexion from the grommet.
3. Grasp the mould of the front sunroof drainage hose and pull it from the recessed gap.
4. Remove the backside group from the drainage hose and Disinfected elsewhere any debris commence inside the abundance. The pieces regularly prompt clogged with miniature debris from the sunroof guides, forcing drool to back up finished the tubes and into the escort channels on the sunroof.
18. Pour a inconsequential amount of water into the entrance of the drainage tube near the rear of the sunroof guide channels and ensure that it flows out of the bottom of the tube without backing up.19.
7. Area the purpose of the sunroof drainage tube into the recessed gap near the floor of the interior.
8. Push the rubber grommet over the gap. On the Chauffeur side of the vehicle, attach the electrical connexion that was formerly removed.
9. Push the kick panel over the grommet to engage the retaining clips on the panel into the mounting holes on the reason of the vehicle.
10. Repeat Steps 1 buttoned up 9 on the contrasted side of the vehicle to assistance the other front drainage tube.
Cleaning the Two Rear Drainage Tubes
11. Remove the fasteners holding the rear rotate splash shield in compass, using wire cutters to gently lift the centre of the fasteners up to disengage the clips. Remove the splash shield from the vehicle.
12. Remove the two Torx screws located in the Timber with a Torx screwdriver that Celebrate the rear tail light in lay. Remove the tail glowing.
13. Loosen the rear quarter panel. Loosen the two bolts at the end the tail bright and another bolt near the Timber hinge with a socket wrench. Remove the two Torx screws surrounded by rubber grommets with a Torx screwdriver near the rear door lock on the rear door opening.
14. Pry the plastic trim out from the vehicle with a miniature screwdriver that is located at the design of the rear door trim.
15. Grasp the design of the rear sunroof drainage hose down the opening under the plastic comprehend and pull it from the recessed gap.
16. Remove the backside collection from the drainage hose and Disinfected gone any debris father inside the lot.
17.Push the backside group back onto the boundary of the sunroof drainage hose.
5. Push the backside collection back onto the foot of the sunroof drainage hose.6. Pour a minor magnitude of damp into the entrance of the drainage tube near the sunroof docent channels and ice that it flows away of the backside of the tube without backing up.
Place the end of the sunroof drainage tube into the recessed hole under the removed plastic cover.
20. Push the plastic trim onto the access hole that is located at the base of the rear door trim.
21. Tighten the rear quarter panel. Tighten the two bolts behind the tail light and another bolt near the trunk hinge with a socket wrench. Install the two Torx screws surrounded by rubber grommets with a Torx screwdriver near the rear door latch on the rear door opening.
22. Place the rear tail light into position and install the Torx screws located in the trunk with a Torx screwdriver.
23. Place the inner splash shield into position and install the fasteners, pushing the bottom of the fasteners into the mounting hole and pushing the center of the fastener down to engage them.
24. Repeat Steps 1 through 13 on the opposite side of the vehicle to service the other rear drainage tube.
