Correct install the brakes on your Ford 500.
Incorrectly installing the CD brakes on your Ford 500 could be the contrariness between getting residence safely and career in a lethal van accident. The Ford Five Hundred is a luxury automobile that uses CD brakes for Everyone circle. The front brakes engage in the majority of the profession and Testament essential to be replaced bounteous ofttimes. Installing virgin brake pads yourself Testament save you both bit and bankroll, by not having to haul the motorcar into the shop.
Instructions
Removing the Brakes
1. End a pump siphon implements to remove half the brake fluid from the crackerjack cylinder reservoir. Domicile one site of the siphon hose into the crackerjack cylinder and the other purpose into a container. Squeeze the pump until brake fluid starts to pace wound up the hose.
2. Country a lug wrench on the lug nuts and turn counterclockwise to loosen the lug nuts until they can be turned by share. It's primary to loosen the nuts before jacking the automobile off the ground so the weight of the machine keeps the tires from spinning. Jack the automobile up off the ground using a van jack and remove the lug nuts and tire by ability.
3. Purpose the CD brake caliper with a pencil to diffenrentiate between the left and honorable sides for likely reference. Loosen the brake caliper bolts with an Allen wrench and disconnect the brake hose from the brake contour. Remove the caliper anchor bolts with a wrench and measure the caliper anchor plate and pads aside.
4. Remove the brake pads from the caliper, then remove the bolts from the caliper anchor plate. Remove the brake pads and spring clips.
Installing the Brakes
5. Position a C-clamp over the caliper piston and tighten the clamp until the piston is fully compressed. This helps fit the brake pads back into city. Install the spring clips and brake pads back in the caliper meeting.
6. Install the brake caliper anchor, using a torque wrench to tighten the anchor bolts to 74 foot-pounds (100 Nm).
7. Install the caliper with the fashionable director pins, using a torque wrench to tighten the bolts to 44 foot-pounds (60 Nm).
8. Install virgin copper washers in the brake hoses. Reconnect the hoses and install the flow bolt with a torque wrench to 22 foot-pounds (30 Nm).
9. Deposit the tire back on, tighten the lug nuts and lower the automobile to the ground. Re-tighten the lug nuts with the lug wrench; you Testament be able to tighten the lugs another with the weight of the automobile holding the tires in put.
10. Repeat the previous steps on other brakes you method to repair.
Bleeding the Brake System
11. Bleed the longest brake border aboriginal. Remove the tank hose from the adapter, then remove the adapter.16. Pump the brake pedal several times to position the brake pads before attempting to move the vehicle.
Open the valve on the bleeder tank. Loosen the right-rear bleeder screw. Leave it open until the brake fluid flows clear without any bubbles, then tighten the bleeder screw and remove the rubber hose.
13. Press and release the parking brake five times. Continue until clear, bubble-free fluid comes out. Tighten the right-rear bleeder screw and install the bleeder cap. Open the valve for the bleeder tank.
14. Loosen the left-rear bleeder screw and leave it open until clear, bubble-free brake fluid flows, then tighten the left-rear bleeder screw and remove the rubber hose. Continue bleeding the front of the system in the order from the right-front disc brake caliper bleeder screw and ending with the left-front brake caliper bleeder screw.
15. Shut the bleeder tank valve. Situate the bleeder adapter on the brake crackerjack cylinder reservoir and connect the bleeder vehicle hose to the becoming on the adapter. Distance a box-end wrench on the right-rear bleeder screw. Connect a rubber void tube to the right-rear bleeder screw and submerge the other cusp of the tube in a container partially comprehensive with Disinfected brake fluid.12.
This will tighten the brake piston in place.
17.Fill the brake master cylinder with brake fluid. Drive the car in a safe area with little traffic to make sure the brakes are working properly.
